View KAD5512HP_4274102.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(R)
KAD5512HP
Data Sheet December 5, 2008 FN6808.0
High Performance 12-Bit, 250/210/170/125MSPS ADC
The KAD5512HP is the high-performance member of the KAD5512 family of 12-bit analog-to-digital converters. Designed with Intersil's proprietary FemtoChargeTM technology on a standard CMOS process, the family supports sampling rates of up to 250MSPS. The KAD5512HP is part of a pin-compatible portfolio of 10, 12 and 14-bit A/Ds with sample rates ranging from 125MSPS to 500MSPS. A serial peripheral interface (SPI) port allows for extensive configurability, as well as fine control of various parameters such as gain and offset. Digital output data is presented in selectable LVDS or CMOS formats. The KAD5512HP is available in 72- and 48-contact QFN packages with an exposed paddle. Operating from a 1.8V supply, performance is specified over the full industrial temperature range (-40C to +85C).
Features
* Pin-Compatible with the KAD5512P Family, Offering 2.5dB Higher SNR * Programmable Gain, Offset and Skew control * 950MHz Analog Input Bandwidth * 60fs Clock Jitter * Over-Range Indicator * Selectable Clock Divider: /1, /2 or /4 * Clock Phase Selection * Nap and Sleep Modes * Two's Complement, Gray Code or Binary Data Format * DDR LVDS-Compatible or LVCMOS Outputs * Programmable Built-in Test Patterns * Single-Supply 1.8V Operation * Pb-Free (RoHS Compliant)
Key Specifications
* SNR = 67.2dBFS for fIN = 124MHz (-1dBFS) * SFDR = 81dBc for fIN = 124MHz (-1dBFS) * Power Consumption - 407/324mW @ 250/125MSPS (SDR Mode) - 368/288mW @ 250/125MSPS (DDR Mode)
CLKDIV
Applications
* Power Amplifier Linearization * Radar and Satellite Antenna Array Processing * Broadband Communications * High-Performance Data Acquisition * Communications Test Equipment
OVDD
AVDD
* WiMAX and Microwave Receivers
CLKP CLKN
Clock Generation
CLKOUTP CLKOUTN
Pin-Compatible Family
MODEL KAD5514P-25 RESOLUTION 14 14 14 14 12 12 12 12 12 10 SPEED (MSPS) 250 210 170 125 500 250 210 170 125 500
D[11:0]P VINP SHA VINN VCM
1.25 V
KAD5514P-21 KAD5514P-17
12-bit 250 MSPS ADC
Digital Error Correction LVDS/CMOS Drivers
D[11:0]N ORP ORN OUTFMT OUTMODE
KAD5514P-12 KAD5512P-50 KAD5512P-25, KAD5512HP-25 KAD5512P-21, KAD5512HP-21 KAD5512P-17, KAD5512HP-17 KAD5512P-12, KAD5512HP-12 KAD5510P-50
+ -
SPI Control
CSB SCLK SDIO SDO
NAPSLP
1
OVSS
AVSS
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. FemtoCharge is a trademark of Kenet Inc. Copyright Intersil Americas Inc. 2008. All Rights Reserved All other trademarks mentioned are the property of their respective owners.
KAD5512HP Ordering Information
PART NUMBER KAD5512HP-25Q72 (Note 2) KAD5512HP-21Q72 (Note 2) KAD5512HP-17Q72 (Note 2) KAD5512HP-12Q72 (Note 2) KAD5512HP-25Q48 (Note 1) KAD5512HP-21Q48 (Note 1) KAD5512HP-17Q48 (Note 1) KAD5512HP-12Q48 (Note 1) NOTES: 1. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD020. 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and NiPdAu plate - e4 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. SPEED (MSPS) 250 210 170 125 250 210 170 125 TEMP. RANGE (C) -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 PACKAGE (Pb-Free) 72 Ld QFN 72 Ld QFN 72 Ld QFN 72 Ld QFN 48 Ld QFN 48 Ld QFN 48 Ld QFN 48 Ld QFN PKG. DWG. # L72.10X10D L72.10X10D L72.10X10D L72.10X10D L48.7X7E L48.7X7E L48.7X7E L48.7X7E
2
FN6808.0 December 5, 2008
KAD5512HP Table of Contents
Absolute Maximum Ratings ......................................... 4 Thermal Information...................................................... 4 Electrical Specifications ............................................... 4 Digital Specifications .................................................... 6 Timing Diagrams ........................................................... 6 Switching Specifications .............................................. 7 Thermal Impedance....................................................... 7 ESD ................................................................................. 7 Pinout/Package Information......................................... 8 Pin Descriptions - 72QFN........................................... Pinout ......................................................................... Pin Descriptions - 48QFN........................................... Pinout ......................................................................... 8 9 10 11 Serial Peripheral Interface ........................................... 19 SPI Physical Interface................................................ SPI Configuration....................................................... Device Information ..................................................... Indexed Device Configuration/Control ....................... Global Device Configuration/Control.......................... Device Test ................................................................ SPI Memory Map ....................................................... 21 21 21 22 23 24 25
Equivalent Circuits ....................................................... 26 Layout Considerations................................................. 27 Split Ground and Power Planes................................. Clock Input Considerations ........................................ Exposed Paddle......................................................... Bypass and Filtering .................................................. LVDS Outputs ............................................................ LVCMOS Outputs ...................................................... Unused Inputs............................................................ 27 27 27 27 27 27 27
Typical Performance Curves ........................................ 12 Theory of Operation ...................................................... 15 Functional Description ................................................ Power-On Calibration ................................................. User-Initiated Reset.................................................... Analog Input ............................................................... Clock Input ................................................................. Jitter............................................................................ Voltage Reference...................................................... Digital Outputs ............................................................ Over-Range Indicator ................................................. Power Dissipation....................................................... Nap/Sleep................................................................... Data Format ............................................................... 15 15 16 16 17 18 18 18 18 18 18 19
Definitions ..................................................................... 27 Revision History ........................................................... 28 Package Outline Drawings........................................... 29 L48.7x7E.................................................................... 29 L72.10x10D................................................................ 30
3
FN6808.0 December 5, 2008
KAD5512HP
Absolute Maximum Ratings
AVDD to AVSS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.4V to 2.1V OVDD to OVSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.4V to 2.1V AVSS to OVSS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 0.3V Analog Inputs to AVSS. . . . . . . . . . . . . . . . . . -0.4V to AVDD + 0.3V Clock Inputs to AVSS. . . . . . . . . . . . . . . . . . . -0.4V to AVDD + 0.3V Logic Input to AVSS . . . . . . . . . . . . . . . . . . . . -0.4V to OVDD + 0.3V Logic Inputs to OVSS. . . . . . . . . . . . . . . . . . . -0.4V to OVDD + 0.3V
Thermal Information
Operating Temperature . . . . . . . . . . . . . . . . . . . . . . .-40C to +85C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65C to +150C Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty.
Electrical Specifications All specifications apply under the following conditions unless otherwise noted: AVDD = 1.8V, OVDD = 1.8V,
TA = -40C to +85C (typical specifications at +25C), AIN = -1dBFS, fSAMPLE = Maximum Conversion Rate (per speed grade). KAD5512HP-25 PARAMETER SYMBOL CONDITIONS MIN TYP KAD5512HP-21 TYP KAD5512HP-17 TYP KAD5512HP-12 TYP MAX UNITS
MAX MIN
MAX MIN
MAX MIN
DC SPECIFICATIONS (Note 3) Analog Input Full-Scale Analog Input Range Input Resistance Input Capacitance Full Scale Range Temp. Drift Input Offset Voltage Gain Error Common-Mode Output Voltage Power Requirements 1.8V Analog Supply Voltage 1.8V Digital Supply Voltage 1.8V Analog Supply Current 1.8V Digital Supply Current (SDR) (Note 3) 1.8V Digital Supply Current (DDR) (Note 3) Power Supply Rejection Ratio Power Dissipation Normal Mode (SDR) Normal Mode (DDR) Nap Mode Sleep Mode PD PD PD PD 3mA LVDS 3mA LVDS 407 368 134 14 438 301 146 16 382 342 129 13 413 279 140 15 355 317 124 12 386 256 136 14 324 288 114 12 353 227 128 13 mW mW mW mW AVDD OVDD IAVDD IOVDD 3mA LVDS 1.7 1.7 1.8 1.8 158 68 1.9 1.9 167 76 1.7 1.7 1.8 1.8 146 66 1.9 1.9 155 74 1.7 1.7 1.8 1.8 133 64 1.9 1.9 142 72 1.7 1.7 1.8 1.8 118 62 1.9 1.9 126 70 V V mA mA VFS RIN CIN AVTC VOS EG VCM Differential Differential Differential Full Temp -10 1.40 1.47 500 2.6 90 2 2 0.535 10 -10 1.54 1.40 1.47 500 2.6 90 2 2 0.535 10 -10 1.54 1.40 1.47 500 2.6 90 2 2 0.535 10 -10 1.54 1.40 1.47 500 2.6 90 2 2 0.535 10 1.54 VP-P pF ppm/C mV % V
IOVDD
3mA LVDS
46
44
43
42
mA
PSRR
30MHz, 200mVP-P signal on AVDD
-36
-36
-36
-36
dB
AC SPECIFICATIONS (Note 4) Differential Nonlinearity Integral Nonlinearity DNL INL -1 0.6 1.3 -1 0.6 1.3 -1 0.6 1.4 -1 0.6 2.0 LSB LSB
4
FN6808.0 December 5, 2008
KAD5512HP
Electrical Specifications All specifications apply under the following conditions unless otherwise noted: AVDD = 1.8V, OVDD = 1.8V,
TA = -40C to +85C (typical specifications at +25C), AIN = -1dBFS, fSAMPLE = Maximum Conversion Rate (per speed grade). (Continued) KAD5512HP-25 PARAMETER Minimum Conversion Rate (Note 5) Maximum Conversion Rate Signal-to-Noise Ratio SYMBOL fS MIN fS MAX SNR fIN = 10MHz fIN = 70MHz fIN = 105MHz fIN = 230MHz fIN = 400MHz fIN = 995MHz Signal-to-Noise and Distortion SINAD fIN = 10MHz fIN = 70MHz fIN = 105MHz fIN = 230MHz fIN = 400MHz fIN = 995MHz Effective Number of Bits (Note 4) ENOB fIN = 10MHz fIN = 70MHz fIN = 105MHz fIN = 230MHz fIN = 400MHz fIN = 995MHz Spurious-Free Dynamic Range SFDR fIN = 10MHz fIN = 70MHz fIN = 105MHz fIN = 230MHz fIN = 400MHz fIN = 995MHz Intermodulation Distortion Channel to Channel Isolation Word Error Rate Full Power Bandwidth NOTES: 3. Digital Supply Current is dependent upon the capacitive loading of the digital outputs. IOVDD specifications apply for 10pF load on each digital output. 4. AC Specifications apply after internal calibration of the ADC is invoked at the given sample rate and temperature. Refer to "Power-On Calibration" on page 15 and "User-Initiated Reset" on page 16 for more details. 5. The DLL Range setting must be changed for low speed operation. See "Serial Peripheral Interface" on page 19 for more detail. WER FPBW IMD fIN = 70MHz fIN = 170MHz fIN = 10MHz fIN = 124MHz 70 10.4 64.5 65.0 250 67.5 67.4 67.2 66.9 65.9 62.2 67.2 67.1 66.6 66.4 64.4 55.0 10.9 10.9 10.8 10.7 10.4 8.8 85 84 83 77 71 57 -91.5 -86.5 90 90 10-12 950 90 90 10-12 950 90 90 10-12 950 70 84 83 80 77 70 85 82 78 76 70 10.5 11 10.9 10.8 11 10.6 11 11 10.9 11.1 10.7 65 67.7 67.5 67 67.9 65.7 68 68 67.4 68.3 66.2 65.5 CONDITIONS MIN TYP KAD5512HP-21 TYP KAD5512HP-17 TYP KAD5512HP-12 TYP MAX UNITS 40 125 68.4 68.3 66.2 68.0 68.0 66.7 66.7 68.6 68.2 68.0 65.3 61.2 68.3 68.3 67.6 68.3 64.3 57.0 11.1 11.1 10.9 11.1 10.4 9.2 84 82 77 76 78 60 -96.5 -93 90 90 10-12 950 MHz MSPS MSPS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS Bits Bits Bits Bits Bits Bits dBc dBc dBc dBc dBc dBc dBFS dBFS dB dB
MAX MIN 40 210
MAX MIN 40 170
MAX MIN 40
68.0 67.8 67.6 67.6
5
FN6808.0 December 5, 2008
KAD5512HP
Digital Specifications
PARAMETER INPUTS Input Current High (RESETN) Input Current Low (RESETN) Input Current High (OUTMODE, NAP/SLP, CLKDIV, OUTFMT) Input Current Low (OUTMODE, NAP/SLP, CLKDIV, OUTFMT) Input Capacitance LVDS OUTPUTS Differential Output Voltage Output Offset Voltage Output Rise Time Output Fall Time CMOS OUTPUTS Voltage Output High Voltage Output Low Output Rise Time Output Fall Time VOH VOL tR tF IOH = -500A IOL = 1mA OVDD - 0.3 OVDD - 0.1 0.1 1.8 1.4 0.3 V V ns ns VT VOS tR tF 3mA Mode 3mA Mode 950 620 965 500 500 980 mVP-P mV ps ps IIH IIL IIH IIL CDI VIN = 1.8V VIN = 0V 0 -25 15 -40 1 -12 25 25 3 10 -5 40 -15 A A A A pF SYMBOL CONDITIONS MIN TYP MAX UNITS
Timing Diagrams
Sample N INP INN tA CLKN CLKP tC PD CLKOUTN CLKOUTP tD C tP D
Odd Bits N-L Even Bit s N-L Odd Bits N-L+1 Even Bits N-L+1 Odd Bits N-L+2 Even Bi ts N-L+2 Odd Bi ts N
Sample N INP INN tA CLKN CLKP
Latency = L Cycles
tC PD CLKOUTN CLKOUTP D[11:0]P D[11:0]N
Latency = L Cycles
D[10/8/6/4/2/0]P D[10/8/6/4/2/0]N
tDC tPD
Data N-L Dat a N-L+1 Dat a N
FIGURE 1A. DDR FIGURE 1. LVDS TIMING DIAGRAMS
Sample N INP INN tA CLKN CLKP tC PD CLKOUT tDC tPD D[10/8/6/4/2/0]
Odd Bits N-L Ev en Bits N-L Odd Bit s N-L+1 Even Bi ts N-L+1 Odd Bits N-L+2 Ev en Bits N-L+2 Odd Bits N
FIGURE 1B. SDR
Sample N INP INN tA CLKN CLKP
Latency = L Cycles
tCP D CLKOUT
Latency = L Cycles
tDC tPD D[11:0]
Data N-L Data N-L+1 Data N
FIGURE 2A. DDR FIGURE 2. CMOS TIMING DIAGRAM
FIGURE 2B. SDR
6
FN6808.0 December 5, 2008
KAD5512HP Switching Specifications
PARAMETER ADC OUTPUT Aperture Delay RMS Aperture Jitter Output Clock to Data Propagation Delay, LVDS Mode DDR Rising Edge DDR Falling Edge SDR Falling Edge Output Clock to Data Propagation Delay, CMOS Mode DDR Rising Edge DDR Falling Edge SDR Falling Edge Latency (Pipeline Delay) Overvoltage Recovery SPI INTERFACE (Notes 6, 7) SCLK Period Write Operation Read Operation SCLK Duty Cycle (tHI/tCLK or tLO/tCLK) SCLK to CSB Setup Time SCLK to CSB Hold Time SCLK to Data Setup Time SCLK to Data Hold Time NOTES: 6. SPI Interface timing is directly proportional to the ADC sample period (tS). Values above reflect multiples of a 4ns sample period, and must be scaled proportionally for lower sample rates. 7. The SPI may operate asynchronously with respect to the ADC sample clock. Read or Write Read or Write Read or Write Read or Write Read or Write tS tH tDS tDH
t CLK
CONDITION
SYMBOL
MIN
TYP
MAX
UNITS
tA jA tDC tDC tDC tDC tDC tDC L tOVR -260 -160 -260 -220 -310 -310
375 60 -50 10 -40 -10 -90 -50 8.5 1 120 230 230 200 110 200
ps fs ps ps ps ps ps ps cycles cycles
64 264 25 -4 -12 -4 -12 50 75
ns ns % ns ns ns ns
tCLK
Thermal Impedance
PARAMETER Junction to Ambient (Note 8) NOTE: 8. Paddle soldered to ground plane. SYMBOL JA 48 LD QFN 72 LD QFN TYP TYP 35 27 UNIT C/W
ESD
Electrostatic charge accumulates on humans, tools and equipment and may discharge through any metallic package contacts (pins, balls, exposed paddle, etc.) of an integrated circuit. Industry-standard protection techniques have been utilized in the design of this product. However, reasonable care must be taken in the storage and handling of ESD sensitive products. Contact Intersil for the specific ESD sensitivity rating of this product.
7
FN6808.0 December 5, 2008
KAD5512HP Pinout/Package Information
Pin Descriptions - 72QFN
PIN NUMBER 1, 6, 12, 19, 24, 71 2-5, 13, 14, 17, 18, 28-31 7, 8, 11, 72 9, 10 15 16 20, 21 22 23 25 26, 45, 55, 65 27, 36, 56 32, 33 34, 35 37, 38 39, 40 41, 42 43, 44 46 47, 48 49, 50 51, 52 53, 54 57, 58 59, 60 61, 62 63, 64 66 67 68 69 70 Exposed Paddle LVDS [LVCMOS] NAME AVDD DNC AVSS VINN, VINP VCM CLKDIV CLKP, CLKN OUTMODE NAPSLP RESETN OVSS OVDD D0N, D0P [NC, D0] D1N, D1P [NC, D1] D2N, D2P [NC, D2] D3N, D3P [NC, D3] D4N, D4P [NC, D4] D5N, D5P [NC, D5] RLVDS LVDS [LVCMOS] FUNCTION 1.8V Analog Supply Do Not Connect Analog Ground Analog Input Negative, Positive Common Mode Output Clock Divider Control Clock Input True, Complement Output Mode (LVDS, LVCMOS) Power Control (Nap, Sleep modes) Power On Reset (Active Low) Output Ground 1.8V Output Supply LVDS Bit 0 (LSB) Output Complement, True [NC, LVCMOS Bit 0] LVDS Bit 1 Output Complement, True [NC, LVCMOS Bit 1] LVDS Bit 2 Output Complement, True [NC, LVCMOS Bit 2] LVDS Bit 3 Output Complement, True [NC, LVCMOS Bit 3] LVDS Bit 4 Output Complement, True [NC, LVCMOS Bit 4] LVDS Bit 5 Output Complement, True [NC, LVCMOS Bit 5] LVDS Bias Resistor (connect to OVSS with a 10k, 1% resistor)
CLKOUTN, CLKOUTP [NC, CLKOUT] LVDS Clock Output Complement, True [NC, LVCMOS CLKOUT] D6N, D6P [NC, D6] D7N, D7P [NC, D7] D8N, D8P [NC, D8] D9N, D9P [NC, D9] D10N, D10P [NC, D10] D11N, D11P [NC, D11] ORN, ORP [NC, OR] SDO CSB SCLK SDIO OUTFMT AVSS LVDS Bit 6 Output Complement, True [NC, LVCMOS Bit 6] LVDS Bit 7 Output Complement, True [NC, LVCMOS Bit 7] LVDS Bit 8 Output Complement, True [NC, LVCMOS Bit 8] LVDS Bit 9 Output Complement, True [NC, LVCMOS Bit 9] LVDS Bit 10 Output Complement, True [NC, LVCMOS Bit 10] LVDS Bit 11(MSB) Output Complement, True [NC, LVCMOS Bit 11] LVDS Over Range Complement, True [NC, LVCMOS Over Range] SPI Serial Data Output (4.7k pull-up to OVDD is required) SPI Chip Select (active low) SPI Clock SPI Serial Data Input/Output Output Data Format (Two's Comp., Gray Code, Offset Binary) Analog Ground
NOTE: LVCMOS Output Mode Functionality is shown in brackets (NC = No Connection)
8
FN6808.0 December 5, 2008
KAD5512HP
Pinout
KAD5512HP (72 LD QFN) TOP VIEW
AVDD DNC DNC DNC DNC AVDD AVSS AVSS VINN VINP AVSS AVDD DNC DNC VCM CLKDIV DNC DNC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37
AVSS AVDD OUTFMT SDIO SCLK CSB SDO OVSS ORP ORN D11P D11N D10P D10N D9P D9N OVDD OVSS
KAD5512
72 QFN
Top View Not to Scale
D8P D8N D7P D7N D6P D6N CLKOUTP CLKOUTN RLVDS OVSS D5P D5N D4P D4N D3P D3N D2P D2N
9
AVDD CLKP CLKN OUTMODE NAPSLP AVDD RESETN OVSS OVDD DNC DNC DNC DNC D0N D0P D1N D1P OVDD
FIGURE 3. 72QFN PIN CONFIGURATION
19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
FN6808.0 December 5, 2008
KAD5512HP
Pin Descriptions - 48QFN
PIN NUMBER 1, 9, 13, 17, 47 2-4, 11, 21, 22 5, 8, 12, 48 6, 7 10 14, 15 16 18 19, 29, 42 20, 37 23, 24 25, 26 27, 28 30 31, 32 33, 34 35, 36 38, 39 40, 41 43 44 45 46 Exposed Paddle LVDS [LVCMOS] NAME AVDD DNC AVSS VINN, VINP VCM CLKP, CLKN NAPSLP RESETN OVSS OVDD D0N, D0P [NC, D0] D1N, D1P [NC, D1] D2N, D2P [NC, D2] RLVDS LVDS [LVCMOS] FUNCTION 1.8V Analog Supply Do Not Connect Analog Ground Analog Input Negative, Positive Common Mode Output Clock Input True, Complement Power Control (Nap, Sleep modes) Power On Reset (Active Low) Output Ground 1.8V Output Supply LVDS Bit 0 (LSB) Output Complement, True [NC, LVCMOS Bit 0] LVDS Bit 1 Output Complement, True [NC, LVCMOS Bit 1] LVDS Bit 2 Output Complement, True [NC, LVCMOS Bit 2] LVDS Bias Resistor (connect to OVSS with a 10k, 1% resistor)
CLKOUTN, CLKOUTP [NC, CLKOUT] LVDS Clock Output Complement, True [NC, LVCMOS CLKOUT] D3N, D3P [NC, D3] D4N, D4P [NC, D4] D5N, D5P [NC, D5] ORN, ORP [NC, OR] SDO CSB SCLK SDIO AVSS LVDS Bit 3 Output Complement, True [NC, LVCMOS Bit 3] LVDS Bit 4 Output Complement, True [NC, LVCMOS Bit 4] LVDS Bit 5 Output Complement, True [NC, LVCMOS Bit 5] LVDS Over Range Complement, True [NC, LVCMOS Over Range] SPI Serial Data Output (4.7k pull-up to OVDD is required) SPI Chip Select (active low) SPI Clock SPI Serial Data Input/Output Analog Ground
NOTE: LVCMOS Output Mode Functionality is shown in brackets (NC = No Connection)
10
FN6808.0 December 5, 2008
KAD5512HP
Pinout
KAD5512HP (48 LD QFN) TOP VIEW
AVDD DNC DNC DNC AVSS VINN VINP AVSS AVDD VCM DNC AVSS
1 2 3 4 5 6 7 8 9 10 11 12
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25
AVSS AVDD SDIO SCLK CSB SDO OVSS ORP ORN D5P D5N OVDD
KAD5512
48 QFN Top View Not to Scale
13 14 15 16 17 18 19 20 21 22 23 24
D4P D4N D3P D3N CLKOUTP CLKOUTN RLVDS OVSS D2P D2N D1P D1N
FIGURE 4. 48QFN PIN CONFIGURATION
11
AVDD CLKP CLKN NAPSLP AVDD RESETN OVSS OVDD DNC DNC D0N D0P
FN6808.0 December 5, 2008
KAD5512HP Typical Performance Curves
All Typical Performance Characteristics apply under the following conditions unless otherwise noted: AVDD = OVDD = 1.8V, TA = +25C, AIN = -1dBFS, fIN = 105MHz, fSAMPLE = Maximum Conversion Rate (per speed grade).
-50
90
HD2 & HD3 MAGNITUDE (dBc)
SNR (dBFS) & SFDR (dBc)
85 80 75 70 65 60 SNR @ 250MSPS 55 50 0 200 400 SNR @ 125MSPS
SFDR @ 125MSPS SFDR @ 250MSPS
-55 -60 HD3 @ 250MSPS -65 HD3 @ 125MSPS -70 -75 -80 -85 HD2 @ 125MSPS -90 HD2 @ 250MSPS
600
800
1000
0
200
400
600
800
1000
INPUT FREQUENCY (MHz)
INPUT FREQUENCY (MHz)
FIGURE 5. SNR AND SFDR vs fIN
FIGURE 6. HD2 AND HD3 vs fIN
100 90 80 70 60 50 40 30 20 10 0 -70 -60 -50 SFDR (dBc)
SFDRFS (dBFS)
-20 -30
HD2 & HD3 MAGNITUDE
-40 -50 -60 -70 -80 -90 -100 -110 -120 HD2 (dBc)
HD3 (dBc)
SNR & SFDR
SNRFS (dBFS)
HD3 (dBFS)
SNR (dBc)
HD2 (dBFS)
-40
-30
-20
-10
0
-70
-60
-50
-40
-30
-20
-10
0
INPUT AMPLITUDE (dBFS)
INPUT AMPLITUDE (dBFS)
FIGURE 7. SNR AND SFDR vs AIN
FIGURE 8. HD2 AND HD3 vs AIN
95.0
-60
SNR (dBFS) & SFDR (dBc)
90.0 SFDR 85.0 80.0 75.0 70.0 65.0 60.0 40 70 100 130 160 190 220 250 SAMPLE RATE (MSPS) SNR
HD2 & HD3 MAGNITUDE (dBc)
-70 HD3 -80 -90 HD2 -100 -110 -120 40 70 100 130 160 190 220 250 SAMPLE RATE (MSPS)
FIGURE 9. SNR AND SFDR vs fSAMPLE
FIGURE 10. HD2 AND HD3 vs fSAMPLE
12
FN6808.0 December 5, 2008
KAD5512HP Typical Performance Curves
All Typical Performance Characteristics apply under the following conditions unless otherwise noted: AVDD = OVDD = 1.8V, TA = +25C, AIN = -1dBFS, fIN = 105MHz, fSAMPLE = Maximum Conversion Rate (per speed grade). (Continued)
1 .5 SDR 1 0 .5 0 -0 .5 -1 -1 .5
450 400
TOTAL POWER (mW)
350 D N L (L SBs) 220 250 300 250 200 150 100 50 0 40 70 100 130 160 190 SAMPLE RATE (MSPS) DDR
0
51 2
1 02 4
1 5 36
20 48 2 56 0 CO DE
3 0 72
35 8 4
4 09 6
FIGURE 11. POWER vs fSAMPLE IN 3mA LVDS MODE
FIGURE 12. DIFFERENTIAL NONLINEARITY
2
90
SNR (dBFS) & SFDR (dBc)
1 .5 1 IN L (LS Bs) 0 .5 0 -0 .5 -1 -1 .5 -2 0 51 2 1 02 4 1 5 36 20 48 2 56 0 CO DE 3 0 72 35 8 4 4 09 6
85 80 75 70 65 60 55 50 300 SNR
SFDR
400
500
600
700
800
INPUT COMMON MODE (mV)
FIGURE 13. INTEGRAL NONLINEARITY
FIGURE 14. SNR AND SFDR vs VCM
80000 70000
A M PLITU D E (d BF S )
0 -20 -40 -60 -80 -1 00 -1 20
A in = -1.0 dBFS S NR = 66. 9 d BFS S FDR = 88. 1 dBc S INA D = 6 6.8 dB FS
NUMBER OF HITS
60000 50000 40000 30000 20000 10000 0 2049 2050 2051 2052 CODE 2053 2054 2055
0
20
40 60 80 FR EQ U EN CY ( M Hz)
1 00
1 20
FIGURE 15. NOISE HISTOGRAM
FIGURE 16. SINGLE-TONE SPECTRUM @ 10MHz
13
FN6808.0 December 5, 2008
KAD5512HP Typical Performance Curves
All Typical Performance Characteristics apply under the following conditions unless otherwise noted: AVDD = OVDD = 1.8V, TA = +25C, AIN = -1dBFS, fIN = 105MHz, fSAMPLE = Maximum Conversion Rate (per speed grade). (Continued)
0
Ain = -1. 0 dBFS SNR = 6 6. 6 d B FS SFDR = 79. 8 d B c SINAD = 66.2 dBFS
0 -20 A M PLIT U D E (d BF S ) -40 -60 -80 -1 00 -1 20
-20 A M PLIT U D E (d BF S ) -40 -60 -80 -1 00 -1 20
A in = -1.1 dBFS S NR = 66. 3 d BFS S FDR = 80. 9 dBc S INA D = 6 6.1 dB FS
0
20
40 60 80 FR EQ U EN CY ( M Hz)
1 00
1 20
0
20
40 60 80 FR EQ U EN CY ( M Hz)
1 00
1 20
FIGURE 17. SINGLE-TONE SPECTRUM @ 137MHz
FIGURE 18. SINGLE-TONE SPECTRUM @ 190MHz
0 -20 A M PLITU D E (d BF S ) -40 -60 -80 -1 00 -1 20
A in = -1.0 dBFS S NR = 64. 0 d BFS S FDR = 73. 6 dBc S INA D = 6 3.6 dB FS
0 -20 A M PLITU D E (d BF S ) -40 -60 -80 -1 00 -1 20
A in = -1.1 dBFS S NR = 61. 9 d BFS S FDR = 52. 9 dBc S INA D = 5 2.7 dB FS
0
20
40 60 80 FR EQ U EN CY ( M Hz)
1 00
1 20
0
20
40 60 80 FR EQ U EN CY ( M Hz)
1 00
1 20
FIGURE 19. SINGLE-TONE SPECTRUM @ 495MHz
FIGURE 20. SINGLE-TONE SPECTRUM @ 995MHz
0 -20 A M PLITU D E (d BF S ) -40 -60 -80 -1 00 -1 20
IMD = -9 0. 3dBFS
0 -20 A M PLITU D E (d BF S ) -40 -60 -80 -1 00 -1 20
IMD = -8 6. 4dBFS
0
20
40 60 80 FR EQ U EN CY ( M Hz)
1 00
1 20
0
20
40 60 80 FR EQ U EN CY ( M Hz)
1 00
1 20
FIGURE 21. TWO-TONE SPECTRUM @ 70MHz
FIGURE 22. TWO-TONE SPECTRUM @ 170MHz
14
FN6808.0 December 5, 2008
KAD5512HP Theory of Operation
Functional Description
The KAD5512HP is based upon a 12-bit, 250MSPS A/D converter core that utilizes a pipelined successive approximation architecture (Figure 23). The input voltage is captured by a Sample-Hold Amplifier (SHA) and converted to a unit of charge. Proprietary charge-domain techniques are used to successively compare the input to a series of reference charges. Decisions made during the successive approximation operations determine the digital code for each input value. The converter pipeline requires six samples to produce a result. Digital error correction is also applied, resulting in a total latency of seven and one half clock cycles. This is evident to the user as a time lag between the start of a conversion and the data being available on the digital outputs. The KAD5512HP family offers 2.5dB improvement in SNR over the KAD5512P by simultaneously sampling the input signal with two ADC cores in parallel and summing the digital result. Since the input signal is correlated between the two cores and noise is not, an increase in SNR is achieved. As a result of this architecture, indexed SPI operations must be executed on each core in series. Refer to "Indexed Device Configuration/Control" on page 22 for more details. ramps and initiates the calibration when the analog and digital supply voltages are above a threshold. The following conditions must be adhered to for the power-on calibration to execute successfully: * A frequency-stable conversion clock must be applied to the CLKP/CLKN pins * DNC pins (especially 3, 4 and 18) must not be pulled up or down * SDO (pin 66) must be high * RESETN (pin 25) must begin low * SPI communications must not be attempted A user-initiated reset can subsequently be invoked in the event that the previous conditions cannot be met at power-up. The SDO pin requires an external 4.7k pull-up to OVDD. If the SDO pin is pulled low externally during power-up, calibration will not be executed properly. After the power supply has stabilized the internal POR releases RESETN and an internal pull-up pulls it high, which starts the calibration sequence. If a subsequent user-initiated reset is required, the RESETN pin should be connected to an open-drain driver with a drive strength of less than 0.5mA.
Power-On Calibration
The ADC performs a self-calibration at start-up. An internal power-on-reset (POR) circuit detects the supply voltage
Clock Generation
INP SHA INN
2.5-bit Flash
6-Stage 1.5-bit/stage
3-Stage 1-bit/stage
3-bit Flash
1.25V
+ -
Digital Error Correction
LVDS/LVCMOS Outputs
FIGURE 23. ADC CORE BLOCK DIAGRAM
15
FN6808.0 December 5, 2008
KAD5512HP
The calibration sequence is initiated on the rising edge of RESETN, as shown in Figure 24. The over-range output (OR) is set high once RESETN is pulled low, and remains in that state until calibration is complete. The OR output returns to normal operation at that time, so it is important that the analog input be within the converter's full-scale range to observe the transition. If the input is in an over-range condition the OR pin will stay high, and it will not be possible to detect the end of the calibration cycle. While RESETN is low, the output clock (CLKOUTP/CLKOUTN) is set low. Normal operation of the output clock resumes at the next input clock edge (CLKP/CLKN) after RESETN is deasserted. At 250MSPS the nominal calibration time is 200ms, while the maximum calibration time is 550ms.
CLKN CLKP Calibration Time RESETN Calibration Begins ORP Calibration Complete CLKOUTP
SFDR CHANGE (dBc 15 10 5 0 -5 -10 -15 -40 -15 10 35 60 85 TEMPERATURE ( C)
over the operating range without recalibrating. The average change in SNR/SFDR is shown, relative to the +25C value.
4 3 SNR CHANGE (dBFS 2 1 0 -1 -2 -3 -4 -40 -15 10 35 60 85 TEMPERATURE (C)
FIGURE 25. SNR PERFORMANCE vs TEMPERATURE AFTER +25C CALIBRATION
FIGURE 24. CALIBRATION TIMING
User-Initiated Reset
Recalibration of the ADC can be initiated at any time by driving the RESETN pin low for a minimum of one clock cycle. An open-drain driver with a drive strength of less than 0.5mA is recommended. As is the case during power-on reset, the SDO, RESETN and DNC pins must be in the proper state for the calibration to successfully execute. The performance of the KAD5512HP changes with variations in temperature, supply voltage or sample rate. The extent of these changes may necessitate recalibration, depending on system performance requirements. Best performance will be achieved by recalibrating the ADC under the environmental conditions at which it will operate. A supply voltage variation of less than 100mV will generally result in an SNR change of less than 0.5dBFS and SFDR change of less than 3dBc. In situations where the sample rate is not constant, best results will be obtained if the device is calibrated at the highest sample rate. Reducing the sample rate by less than 80MSPS will typically result in an SNR change of less than 0.5dBFS and an SFDR change of less than 3dBc. Figures 25 and 26 show the effect of temperature on SNR and SFDR performance without recalibration. In each plot the ADC is calibrated at +25C and temperature is varied
FIGURE 26. SFDR PERFORMANCE vs TEMPERATURE AFTER +25C CALIBRATION
Analog Input
A single fully differential input (VINP/VINN) connects to the sample and hold amplifier (SHA) of each unit ADC. The ideal full-scale input voltage is 1.45V, centered at the VCM voltage of 0.535V as shown in Figure 27.
1.8 1.4 1.0 0.6 0.2 0.725V INP VCM 0.535V INN
FIGURE 27. ANALOG INPUT RANGE
16
FN6808.0 December 5, 2008
KAD5512HP
Best performance is obtained when the analog inputs are driven differentially. The common-mode output voltage, VCM, should be used to properly bias the inputs as shown in Figures 28 through 30. An RF transformer will give the best noise and distortion performance for wideband and/or high intermediate frequency (IF) inputs. Two different transformer input schemes are shown in Figures 28 and 29.
ADT1-1WT 1000pF ADT1-1WT
A differential amplifier, as shown in Figure 30, can be used in applications that require DC-coupling. In this configuration the amplifier will typically dominate the achievable SNR and distortion performance.
Clock Input
The clock input circuit is a differential pair (see Figure 44). Driving these inputs with a high level (up to 1.8VP-P on each input) sine or square wave will provide the lowest jitter performance. A transformer with 4:1 impedance ratio will provide increased drive levels. The recommended drive circuit is shown in Figure 31. A duty range of 40% to 60% is acceptable. The clock can be driven single-ended, but this will reduce the edge rate and may impact SNR performance. The clock inputs are internally self-biased to AVDD/2 to facilitate AC-coupling.
200pF TC4-1W CLKP 1000pF 200O CLKN 200pF
KAD5512HP
VCM
0.1F
FIGURE 28. TRANSFORMER INPUT FOR GENERAL PURPOSE APPLICATIONS
ADTL1-12 1000pF 1000pF
ADTL1-12 0.1F KAD5512HP
VCM
200pF
FIGURE 29. TRANSMISSION-LINE TRANSFORMER INPUT FOR HIGH IF APPLICATIONS
FIGURE 31. RECOMMENDED CLOCK DRIVE
This dual transformer scheme is used to improve commonmode rejection, which keeps the common-mode level of the input matched to VCM. The value of the shunt resistor should be determined based on the desired load impedance. The differential input resistance of the KAD5512HP is 500. The SHA design uses a switched capacitor input stage (see Figure 43), which creates current spikes when the sampling capacitance is reconnected to the input voltage. This causes a disturbance at the input which must settle before the next sampling point. Lower source impedance will result in faster settling and improved performance. Therefore a 1:1 transformer and low shunt resistance are recommended for optimal performance.
348O 69.8O 100O
217O
CM
A selectable 2x frequency divider is provided in series with the clock input. The divider can be used in the 2x mode with a sample clock equal to twice the desired sample rate. This allows the use of the Phase Slip feature, which enables synchronization of multiple ADCs.
TABLE 1. CLKDIV PIN SETTINGS CLKDIV PIN AVSS Float AVDD DIVIDE RATIO 2 1 4
The clock divider can also be controlled through the SPI port, which overrides the CLKDIV pin setting. Details on this are contained in "Serial Peripheral Interface" on page 19. A delay-locked loop (DLL) generates internal clock signals for various stages within the charge pipeline. If the frequency of the input clock changes, the DLL may take up to 52s to regain lock at 250MSPS. The lock time is inversely proportional to the sample rate. The DLL has two ranges of operation, slow and fast. The slow range can be used for sample rates between 40MSPS and 100MSPS, while the default fast range can be used from 80MSPS to the maximum specified sample rate.
25O
KAD5512HP
VCM
0.22F
100O 69.8O
49.9O
25O 348O
0.1F
FIGURE 30. DIFFERENTIAL AMPLIFIER INPUT
17
FN6808.0 December 5, 2008
KAD5512HP
Jitter
In a sampled data system, clock jitter directly impacts the achievable SNR performance. The theoretical relationship between clock jitter (tJ) and SNR is shown in Equation 1 and is illustrated in Figure 32.
1 SNR = 20 log 10 ------------------- 2f t
IN J
10 0 95 tj=0.1p s 90 85 1 4 Bits
physical proximity to the ADC. The applicability of this setting is dependent upon the PCB layout, therefore the user should experiment to determine if performance degradation is observed. The output mode and LVDS drive current are selected via the OUTMODE pin as shown in Table 2.
TABLE 2. OUTMODE PIN SETTINGS OUTMODE PIN AVSS Float AVDD MODE LVCMOS LVDS, 3mA LVDS, 2mA
(EQ. 1)
SNR - dB
80 75 70 65 60 55 50 1 10 tj=1 00p s tj=1 0p s
tj=1 ps
1 2 Bits
10 Bits
The output mode can also be controlled through the SPI port, which overrides the OUTMODE pin setting. Details on this are contained in "Serial Peripheral Interface" on page 19.
10 00
100
Input Frequency - MHz
FIGURE 32. SNR vs CLOCK JITTER
An external resistor creates the bias for the LVDS drivers. A 10k, 1% resistor must be connected from the RLVDS pin to OVSS.
This relationship shows the SNR that would be achieved if clock jitter were the only non-ideal factor. In reality, achievable SNR is limited by internal factors such as linearity, aperture jitter and thermal noise. Internal aperture jitter is the uncertainty in the sampling instant shown in Figure 1 on page 6. The internal aperture jitter combines with the input clock jitter in a root-sum-square fashion, since they are not statistically correlated, and this determines the total jitter in the system. The total jitter, combined with other noise sources, then determines the achievable SNR.
Over-Range Indicator
The over-range (OR) bit is asserted when the output code reaches positive full-scale (e.g. 0xFFF in offset binary mode). The output code does not wrap around during an over-range condition. The OR bit is updated at the sample rate.
Power Dissipation
The power dissipated by the KAD5512HP is primarily dependent on the sample rate and the output modes: LVDS vs CMOS and DDR vs SDR. There is a static bias in the analog supply, while the remaining power dissipation is linearly related to the sample rate. The output supply dissipation changes to a lesser degree in LVDS mode, but is more strongly related to the clock frequency in CMOS mode.
Voltage Reference
A temperature compensated voltage reference provides the reference charges used in the successive approximation operations. The full-scale range of each A/D is proportional to the reference voltage. The voltage reference is internally bypassed and is not accessible to the user.
Nap/Sleep
Portions of the device may be shut down to save power during times when operation of the ADC is not required. Two power saving modes are available: Nap, and Sleep. Nap mode reduces power dissipation to less than 134mW and recovers to normal operation in approximately 1s. Sleep mode reduces power dissipation to less than 14mW but requires 1ms to recover. All digital outputs (Data, CLKOUT and OR) are placed in a high impedance state during Nap or Sleep. The input clock should remain running and at a fixed frequency during Nap or Sleep. Recovery time from Nap mode will increase if the clock is stopped, since the internal DLL can take up to 52s to regain lock at 250MSPS. By default after the device is powered on, the operational state is controlled by the NAPSLP pin as shown in Table 3.
Digital Outputs
Output data is available as a parallel bus in LVDS-compatible or CMOS modes. Additionally, the data can be presented in either double data rate (DDR) or single data rate (SDR) formats. The even numbered output bits are active in DDR mode. When CLKOUT is low the MSB and all odd bits are output, while on the high phase the LSB and all even bits are presented. Figures 1 and 2 show the timing relationships for LVDS/CMOS and DDR/SDR modes. The 48 Ld QFN package option contains six LVDS data outputs, and therefore can only support DDR mode. Additionally, the drive current for LVDS mode can be set to a nominal 3mA or a power-saving 2mA. The lower current setting can be used in designs where the receiver is in close
18
FN6808.0 December 5, 2008
KAD5512HP
TABLE 3. NAPSLP PIN SETTINGS
Gray Code
NAPSLP PIN AVSS Float AVDD MODE Normal Sleep Nap
11
10
9
****
1
0
****
The power-down mode can also be controlled through the SPI port, which overrides the NAPSLP pin setting. Details on this are contained in "Serial Peripheral Interface" on page 19. This is an indexed function when controlled from the SPI, but a global function when driven from the pin.
****
Data Format
Output data can be presented in three formats: two's complement, Gray code and offset binary. The data format is selected via the OUTFMT pin as shown in Table 4.
TABLE 4. OUTFMT PIN SETTINGS OUTFMT PIN AVSS Float AVDD MODE Offset Binary Two's Complement Gray Code
Binary
11
10
9
****
1
0
FIGURE 34. GRAY CODE TO BINARY CONVERSION
Mapping of the input voltage to the various data formats is shown in Table 5.
TABLE 5. INPUT VOLTAGE TO OUTPUT CODE MAPPING INPUT TWO'S VOLTAGE OFFSET BINARY COMPLEMENT GRAY CODE
The data format can also be controlled through the SPI port, which overrides the OUTFMT pin setting. Details on this are contained in "Serial Peripheral Interface" on page 19. Offset binary coding maps the most negative input voltage to code 0x000 (all zeros) and the most positive input to 0xFFF (all ones). Two's complement coding simply complements the MSB of the offset binary representation. When calculating Gray code, the MSB is unchanged. The remaining bits are computed as the XOR of the current bit position and the next most significant bit. Figure 33 shows this operation.
-Full Scale 000 00 000 00 00 100 00 000 00 00 000 00 000 00 00 -Full Scale 000 00 000 00 01 100 00 000 00 01 000 00 000 00 01 + 1LSB Mid-Scale 100 00 000 00 00 000 00 000 00 00 110 00 000 00 00 +Full Scale - 1LSB +Full Scale 111 11 111 11 10 111 11 111 11 11 011 11 111 11 10 100 00 000 00 01 011 11 111 111 1 100 00 000 00 00
Serial Peripheral Interface
A serial peripheral interface (SPI) bus is used to facilitate configuration of the device and to optimize performance. The SPI bus consists of chip select (CSB), serial clock (SCLK) serial data input (SDI) and serial data input/output (SDIO). The maximum SCLK rate is equal to the ADC sample rate (fSAMPLE) divided by 16 for write operations and fSAMPLE divided by 66 for reads. At fSAMPLE = 250MHz, maximum SCLK is 15.63MHz for writing and 3.79MHz for write operations. There is no minimum SCLK rate. The following sections describe various registers that are used to configure the SPI or adjust performance or functional parameters. Many registers in the available address space (0x00 to 0xFF) are not defined in this document. Additionally, within a defined register there may be certain bits or bit combinations that are reserved. Undefined registers and undefined values within defined registers are reserved and should not be selected. Setting any reserved register or value may produce indeterminate results.
Binary
11
10
9
****
1
0
****
Gray Code 11 10 9 **** 1 0
FIGURE 33. BINARY TO GRAY CODE CONVERSION
Converting back to offset binary from Gray code must be done recursively, using the result of each bit for the next lower bit as shown in Figure 34.
19
FN6808.0 December 5, 2008
KAD5512HP
CSB
SCLK
SDIO
R/W
W1
W0
A12
A11
A10
A1
A0
D7
D6
D5
D4
D3
D2
D1
D0
FIGURE 35. MSB-FIRST ADDRESSING
CSB
SCLK
SDIO
A0
A1
A2
A11
A12
W0
W1
R/W
D0
D1
D2
D3
D4
D5
D6
D7
FIGURE 36. LSB-FIRST ADDRESSING
tS tDS
CSB
tCLK tHI tDH tLO
tH
SCLK
SDIO
R/W
W1
W0
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
FIGURE 37. INSTRUCTION/ADDRESS PHASE
CSB
CSB Stalling
SCLK
SDIO
Instruction/Address
Data Word 1
Data Word 2
FIGURE 38. 2-BYTE TRANSFER
CSB
Last Legal CSB Stalling
SCLK
SDIO
Instruction/Address
Data Word 1
Data Word N
FIGURE 39. N-BYTE TRANSFER
20
FN6808.0 December 5, 2008
KAD5512HP
SPI Physical Interface
The serial clock pin (SCLK) provides synchronization for the data transfer. By default, all data is presented on the serial data input/output (SDIO) pin in three-wire mode. The state of the SDIO pin is set automatically in the communication protocol (described in the following). A dedicated serial data output pin (SDO) can be activated by setting 0x00[7] high to allow operation in four-wire mode. The SPI port operates in a half duplex master/slave configuration, with the KAD5512HP functioning as a slave. Multiple slave devices can interface to a single master in four-wire mode only, since the SDIO output of an unaddressed device is asserted in three wire mode. The chip-select bar (CSB) pin determines when a slave device is being addressed. Multiple slave devices can be written to concurrently, but only one slave device can be read from at a given time (again, only in four-wire mode). If multiple slave devices are selected for reading at the same time, the results will be indeterminate. The communication protocol begins with an instruction/address phase. The first rising SCLK edge following a high-to-low transition on CSB determines the beginning of the two-byte instruction/address command. Data can be presented in MSB-first order or LSB-first order. The default is MSB-first, but this can be changed by setting 0x00[6] high. Figures 35 and 36 show the appropriate bit ordering for the MSB-first and LSB-first modes, respectively. In MSB-first mode the address is incremented for multi-byte transfers, while in LSB-first mode it's decremented. In the default mode the MSB is R/W, which determines if the data is to be read (active high) or written. The next two bits, W1 and W0, determine the number of data bytes to be read or written (see Table 6). The lower 13 bits contain the first address for the data transfer. This relationship is illustrated in Figure 37, and timing values are given in "Switching Specifications" on page 7. After the instruction/address bytes have been read, the appropriate number of data bytes are written to or read from the ADC (based on the R/W bit status). The data transfer will continue as long as CSB remains low and SCLK is active. Stalling of the CSB pin is allowed at any byte boundary (instruction/address or data) if the number of bytes being transferred is three or less. For transfers of four bytes or more, CSB is allowed stall in the middle of the instruction/address bytes or before the first data byte. If CSB transitions to a high state after that point the state machine will reset and terminate the data transfer.
TABLE 6. BYTE TRANSFER SELECTION [W1:W0] 00 01 10 11 BYTES TRANSFERRED 1 2 3 4 or more
Figures 38 and 39 illustrate the timing relationships for 2-byte and N-byte transfers, respectively. The operation for a 3-byte transfer can be inferred from these diagrams.
SPI Configuration
ADDRESS 0X00: CHIP_PORT_CONFIG Bit ordering and SPI reset are controlled by this register. Bit order can be selected as MSB to LSB (MSB first) or LSB to MSB (LSB first) to accommodate various microcontrollers. Bit 7 SDO Active Bit 6 LSB First Setting this bit high configures the SPI to interpret serial data as arriving in LSB to MSB order. Bit 5 Soft Reset Setting this bit high resets all SPI registers to default values. Bit 4 Reserved This bit should always be set high. Bits 3:0 These bits should always mirror bits 4:7 to avoid ambiguity in bit ordering. ADDRESS 0X02: BURST_END If a series of sequential registers are to be set, burst mode can improve throughput by eliminating redundant addressing. In 3-wire SPI mode the burst is ended by pulling the CSB pin high. If the device is operated in 2-wire mode the CSB pin is not available. In that case, setting the burst_end address determines the end of the transfer. During a write operation, the user must be cautious to transmit the correct number of bytes based on the starting and ending addresses. Bits 7:0 Burst End Address This register value determines the ending address of the burst data.
Device Information
ADDRESS 0X08: CHIP_ID ADDRESS 0X09: CHIP_VERSION The generic die identifier and a revision number, respectively, can be read from these two registers.
21
FN6808.0 December 5, 2008
KAD5512HP
Indexed Device Configuration/Control
ADDRESS 0X10: DEVICE_INDEX_A A common SPI map, which can accommodate single-channel or multi-channel devices, is used for all Intersil ADC products. Certain configuration commands (identified as Indexed in the SPI map) can be executed on a per-converter basis. This register determines which converter is being addressed for an Indexed command. It is important to note that only a single converter can be addressed at a time. This register defaults to 00h, indicating that no ADC is addressed. Error code `AD' is returned if any indexed register is read from without properly setting device_index_A. ADDRESS 0X20: OFFSET_COARSE ADDRESS 0X21: OFFSET_FINE The input offset of each ADC core can be adjusted in fine and coarse steps. Both adjustments are made via an 8-bit word as detailed in Table 7. The default value of each register will be the result of the self-calibration after initial power-up. If a register is to be incremented or decremented, the user should first read the register value then write the incremented or decremented value back to the same register.
TABLE 7. OFFSET ADJUSTMENTS PARAMETER Steps -Full Scale (0x00) Mid-Scale (0x80) +Full Scale (0xFF) Nominal Step Size 0x20[7:0] COARSE OFFSET 255 -133LSB (-47mV) 0.0LSB (0.0mV) +133LSB (+47mV) 1.04LSB (0.37mV) 0x21[7:0] FINE OFFSET 255 -5LSB (-1.75mV) 0.0LSB +5LSB (+1.75mV) 0.04LSB (0.014mV) VALUE 000 001 0x22[3:0] 1100 1000 0100 0000 0001 0010 0011 TABLE 8. COARSE GAIN ADJUSTMENT NOMINAL COARSE GAIN ADJUST (%) 4.2 2.8 1.4 0.0 -1.4 -2.8 -4.2
TABLE 9. MEDIUM AND FINE GAIN ADJUSTMENTS PARAMETER Steps -Full Scale (0x00) Mid-Scale (0x80) +Full Scale (0xFF) Nominal Step Size 0x23[7:0] MEDIUM GAIN 256 -2% 0.00% +2% 0.016% 0x24[7:0] FINE GAIN 256 -0.20% 0.00% +0.2% 0.0016%
ADDRESS 0X25: MODES Two distinct reduced power modes can be selected. By default, the tri-level NAPSLP pin can select normal operation, nap or sleep modes (refer to "Nap/Sleep" on page 18). This functionality can be overridden and controlled through the SPI. This is an indexed function when controlled from the SPI, but a global function when driven from the pin. This register is not changed by a Soft Reset.
TABLE 10. POWER-DOWN CONTROL 0x25[2:0] POWER-DOWN MODE Pin Control Normal Operation Nap Mode Sleep Mode
ADDRESS 0X22: GAIN_COARSE ADDRESS 0X23: GAIN_MEDIUM ADDRESS 0X24: GAIN_FINE Gain of each ADC core can be adjusted in coarse, medium and fine steps. Coarse gain is a 4-bit adjustment while medium and fine are 8-bit. The default value of each register will be the result of the self-calibration after initial power-up. If a register is to be incremented or decremented, the user should first read the register value then write the incremented or decremented value back to the same register.
010 100
22
FN6808.0 December 5, 2008
KAD5512HP
Global Device Configuration/Control
ADDRESS 0X70: SKEW_DIFF The value in the skew_diff register adjusts the timing skew between the two ADCs cores. The nominal range and resolution of this adjustment are given in Table 11. The default value of this register after power-up is 80h.
TABLE 11. DIFFERENTIAL SKEW ADJUSTMENT PARAMETER Steps -Full Scale (0x00) Mid-Scale (0x80) +Full Scale (0xFF) Nominal Step Size 0x70[7:0] DIFFERENTIAL SKEW 256 -6.5ps 0.0ps +6.5ps 51fs
ADDRESS 0X72: CLOCK_DIVIDE The KAD5512HP has a selectable clock divider that can be set to divide by four, two or one (no division). By default, the tri-level CLKDIV pin selects the divisor (refer to "Clock Input Considerations" on page 27). This functionality can be overridden and controlled through the SPI, as shown in Table 12. This register is not changed by a Soft Reset.
TABLE 12. CLOCK DIVIDER SELECTION VALUE 000 001 010 100 0x72[2:0] CLOCK DIVIDER Pin Control Divide by 1 Divide by 2 Divide by 4
ADDRESS 0X71: PHASE_SLIP When using the clock divider, it's not possible to determine the synchronization of the incoming and divided clock phases. This is particularly important when multiple ADCs are used in a time-interleaved system. The phase slip feature allows the rising edge of the divided clock to be advanced by one input clock cycle, as shown in Figures 40 and 41. This register is self-clearing.
CLK = CLKP - CLKN CLK
2. 00 ns
ADDRESS 0X73: OUTPUT_MODE_A The output_mode_A register controls the physical output format of the data, as well as the logical coding. The KAD5512HP can present output data in two physical formats: LVDS or LVCMOS. Additionally, the drive strength in LVDS mode can be set high (3mA) or low (2mA). By default, the tri-level OUTMODE pin selects the mode and drive level (refer to "Digital Outputs" on page 18). This functionality can be overridden and controlled through the SPI, as shown in Table 13. Data can be coded in three possible formats: two's complement, Gray code or offset binary. By default, the tri-level OUTFMT pin selects the data format (refer to "Data Format" on page 19). This functionality can be overridden and controlled through the SPI, as shown in Table 14. This register is not changed by a Soft Reset.
TABLE 13. OUTPUT MODE CONTROL
CLK/2
4.00 ns
CLK/2 Slip Once
CLK/2 S lip Twice
VALUE 000 001
CLK = CLKP - CLKN
0x93[7:5] OUTPUT MODE Pin Control LVDS 2mA LVDS 3mA LVCMOS
FIGURE 40. PHASE SLIP: CLK/2 MODE, fCLOCK = 500MHz
010 100
CLK
1. 00 ns
TABLE 14. OUTPUT FORMAT CONTROL VALUE 000 001 010 0x93[2:0] OUTPUT FORMAT Pin Control Two's Complement Gray Code Offset Binary
CLK/4
4.00 ns
CLK/4 Slip Once
CLK/4 Slip Twice
100
FIGURE 41. PHASE SLIP: CLK/4 MODE, fCLOCK = 1000MHz
23
FN6808.0 December 5, 2008
KAD5512HP
ADDRESS 0X74: OUTPUT_MODE_B ADDRESS 0X75: CONFIG_STATUS Bit 6 DLL Range This bit sets the DLL operating range to fast (default) or slow. Bit 4 DDR Enable Setting this bit enables Double Data-Rate mode. Internal clock signals are generated by a delay-locked loop (DLL), which has a finite operating range. Table 15 shows the allowable sample rate ranges for the slow and fast settings.
TABLE 15. DLL RANGES DLL RANGE Slow Fast MIN 40 80 MAX 100 fS MAX UNIT MSPS MSPS
Device Test
The KAD5512HP can produce preset or user defined patterns on the digital outputs to facilitate in-situ testing. A static word can be placed on the output bus, or two different words can alternate. In the alternate mode, the values defined as Word 1 and Word 2 (as shown in Table 16) are set on the output bus on alternating clock phases. The test mode is enabled asynchronously to the sample clock, therefore several sample clock cycles may elapse before the data is present on the output bus. ADDRESS 0XC0: TEST_IO Bits 7:6 User Test Mode These bits set the test mode to static (0x00) or alternate (0x01) mode. Other values are reserved. The four LSBs in this register (Output Test Mode) determine the test pattern in combination with registers 0xC2 through 0xC5. Refer to Table 17.
TABLE 16. OUTPUT TEST MODES
The output_mode_B and config_status registers are used in conjunction to enable DDR mode and select the frequency range of the DLL clock generator. The method of setting these options is different from the other registers.
Read output_mode_B 0x74 Read config_status 0x75 Desired Value
VALUE 0000 0001 0010 0011
0xC0[3:0] OUTPUT TEST MODE Off Midscale Positive Full-Scale Negative Full-Scale Checkerboard Reserved Reserved One/Zero User Pattern
WORD 1
WORD 2
0x8000 0xFFFF 0x0000 0xAAAA N/A N/A 0xFFFF user_patt1
N/A N/A N/A 0x5555 N/A N/A 0x0000 user_patt2
Write to 0x74
0100 0101 0110 0111 1000
FIGURE 42. SETTING OUTPUT_MODE_B REGISTER
The procedure for setting output_mode_B is shown in Figure 42. Read the contents of output_mode_B and config_status and XOR them. Then XOR this result with the desired value for output_mode_B and write that XOR result to the register.
ADDRESS 0XC2: USER_PATT1_LSB ADDRESS 0XC3: USER_PATT1_MSB These registers define the lower and upper eight bits, respectively, of the first user-defined test word. ADDRESS 0XC4: USER_PATT2_LSB ADDRESS 0XC5: USER_PATT2_MSB These registers define the lower and upper eight bits, respectively, of the second user-defined test word.
24
FN6808.0 December 5, 2008
KAD5512HP
SPI Memory Map
TABLE 17. SPI MEMORY MAP
Addr (Hex) 00 01 02 03-07 08 09 10 11-1F 20 21 22 23 24 25 Info SPI Config Parameter Name port_config reserved burst_end reserved chip_id chip_version device_index_A reserved offset_coarse offset_fine gain_coarse gain_medium gain_fine modes Bit 7 (MSB) SDO Active Bit 6 LSB First Bit 5 Soft Reset Reserved Burst end address [7:0] Reserved Chip ID # Chip Version # Reserved ADC01 Reserved Coarse Offset Fine Offset Medium Gain Fine Gain ADC00 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) Mirror (bit7) Def. Value Indexed/ (Hex) Global 00h 00h Read only Read only 00h cal. value cal. value cal. value cal. value cal. value 00h NOT affected by Soft Reset G G G G I I I I I I I
Mirror (bit5) Mirror (bit6)
Indexed Device Config /Control
Reserved
Coarse Gain
Power Down Mode [2:0] 000=Pin Control 001=Normal Operation 010=Nap 100=Sleep other codes=reserved
26-5F 60-6F 70 71 72 Global Device Config/Control
reserved reserved reserved phase_slip clock_divide
Reserved Reserved Reserved Reserved Clock Divide [2:0] 000=Pin Control 001=divide by 1 010=divide by 2 100=divide by 4 other codes=reserved Output Format [2:0] 000=Pin Control 001=Twos Complement 010=Gray Code 100=Offset Binary other codes=reserved DDR Enable Next Clock Edge 00h 00h NOT affected by Soft Reset G G
73
output_mode_A
74
output_mode_B
Output Mode [2:0] 000=Pin Control 001=LVDS 2mA 010=LVDS 3mA 100=LVCMOS other codes=reserved DLL Range 0=fast 1=slow
00h NOT affected by Soft Reset
G
00h NOT affected by Soft Reset Read Only Output Test Mode [3:0] 7=One/Zero Word Togg le 8=User Input 9-15=reserved 00h
G
75 76-BF C0
config_status reserved test _io
XOR Result User Test M ode [2:0] 00=Single 01=Alt ernate 10=Single Once 11=Alt ernate Once Reset PN Long Gen
XOR Result Reserved Reset PN Short Gen 0=Off
G G
Device Test
1=Midscale Short 2=+FS Short 3=- FS Short 4=Checker Board 5=reserved 6=reserved B5 B13 B5 B13 B4 B12 B4 B12 Reserved B3 B11 B3 B11 Reserved B2 B10 B2 B10
C1 C2 C3 C4 C5 C6-FF
Reserved user_patt 1_lsb user_patt 1_msb user_patt 2_lsb user_patt 2_msb reserved
B7 B15 B7 B15
B6 B14 B6 B14
B1 B9 B1 B9
B0 B8 B0 B8
00h 00h 00h 00h 00h
G G G G G
25
FN6808.0 December 5, 2008
KAD5512HP Equivalent Circuits
AVDD
AVDD
AVDD Csamp 1.6pF
To Clock-Phase Generation AVDD
11kO
INP F 2 F 3
To Charge Pipeline
CLKP
1000O
F1
18kO
Csamp 1.6pF
AVDD INN
To Charge Pipeline F 3
F1
2 F
AVDD 11kO
18kO
CLKN
FIGURE 43. ANALOG INPUTS
FIGURE 44. CLOCK INPUTS
AVDD AVDD
75kO
AVDD
AVDD AVDD
To Sense Logic
AVDD
75kO 280O
280O Input
Input
75kO
To Logic
75kO
FIGURE 45. TRI-LEVEL DIGITAL INPUTS
FIGURE 46. DIGITAL INPUTS
OVDD 2mA or 3mA OVDD DATA DATA D[11:0]P OVDD
D[11:0]N
OVDD OVDD
DATA
DATA
DATA
2mA or 3mA
D[11:0]
FIGURE 47. LVDS OUTPUTS
FIGURE 48. CMOS OUTPUTS
26
FN6808.0 December 5, 2008
KAD5512HP Equivalent Circuits
(Continued)
AVDD
VCM 0.535V + -
FIGURE 49. VCM_OUT OUTPUT
Layout Considerations
Split Ground and Power Planes
Data converters operating at high sampling frequencies require extra care in PC board layout. Many complex board designs benefit from isolating the analog and digital sections. Analog supply and ground planes should be laid out under signal and clock inputs. Locate the digital planes under outputs and logic pins. Grounds should be joined under the chip.
floating if they are not used. Tri-level inputs (NAPSLP, OUTMODE, OUTFMT, CLKDIV) accept a floating input as a valid state, and therefore should be biased according to the desired functionality.
Definitions
Analog Input Bandwidth is the analog input frequency at which the spectral output power at the fundamental frequency (as determined by FFT analysis) is reduced by 3dB from its full-scale low-frequency value. This is also referred to as Full Power Bandwidth. Aperture Delay or Sampling Delay is the time required after the rise of the clock input for the sampling switch to open, at which time the signal is held for conversion. Aperture Jitter is the RMS variation in aperture delay for a set of samples. Clock Duty Cycle is the ratio of the time the clock wave is at logic high to the total time of one clock period. Differential Non-Linearity (DNL) is the deviation of any code width from an ideal 1 LSB step. Effective Number of Bits (ENOB) is an alternate method of specifying Signal to Noise-and-Distortion Ratio (SINAD). In dB, it is calculated as: ENOB = (SINAD - 1.76)/6.02 Gain Error is the ratio of the difference between the voltages that cause the lowest and highest code transitions to the full-scale voltage less 2 LSB. It is typically expressed in percent. Integral Non-Linearity (INL) is the maximum deviation of the ADC's transfer function from a best fit line determined by a least squares curve fit of that transfer function, measured in units of LSBs. Least Significant Bit (LSB) is the bit that has the smallest value or weight in a digital word. Its value in terms of input voltage is VFS/(2N-1) where N is the resolution in bits. Missing Codes are output codes that are skipped and will never appear at the ADC output. These codes cannot be reached with any input value.
Clock Input Considerations
Use matched transmission lines to the transformer inputs for the analog input and clock signals. Locate transformers and terminations as close to the chip as possible.
Exposed Paddle
The exposed paddle must be electrically connected to analog ground (AVSS) and should be connected to a large copper plane using numerous vias for optimal thermal performance.
Bypass and Filtering
Bulk capacitors should have low equivalent series resistance. Tantalum is a good choice. For best performance, keep ceramic bypass capacitors very close to device pins. Longer traces will increase inductance, resulting in diminished dynamic performance and accuracy. Make sure that connections to ground are direct and low impedance. Avoid forming ground loops.
LVDS Outputs
Output traces and connections must be designed for 50 (100 differential) characteristic impedance. Keep traces direct and minimize bends where possible. Avoid crossing ground and power-plane breaks with signal traces.
LVCMOS Outputs
Output traces and connections must be designed for 50 characteristic impedance.
Unused Inputs
Standard logic inputs (RESETN, CSB, SCLK, SDIO, SDO) which will not be operated do not require connection to ensure optimal ADC performance. These inputs can be left
27
FN6808.0 December 5, 2008
KAD5512HP
Most Significant Bit (MSB) is the bit that has the largest value or weight. Pipeline Delay is the number of clock cycles between the initiation of a conversion and the appearance at the output pins of the data. Power Supply Rejection Ratio (PSRR) is the ratio of the observed magnitude of a spur in the ADC FFT, caused by an AC signal superimposed on the power supply voltage. Signal to Noise-and-Distortion (SINAD) is the ratio of the RMS signal amplitude to the RMS sum of all other spectral components below one half the clock frequency, including harmonics but excluding DC. Signal-to-Noise Ratio (without Harmonics) is the ratio of the RMS signal amplitude to the RMS sum of all other spectral components below one-half the sampling frequency, excluding harmonics and DC. SNR and SINAD are either given in units of dB when the power of the fundamental is used as the reference, or dBFS (dB to full scale) when the converter's full-scale input power is used as the reference. Spurious-Free-Dynamic Range (SFDR) is the ratio of the RMS signal amplitude to the RMS value of the largest spurious spectral component. The largest spurious spectral component may or may not be a harmonic.
Revision History
DATE 7/30/08 10/29/08 REVISION Rev 1 CHANGE Initial Release of Production Datasheet
FN6808.0 Converted to intersil template. Assigned file number FN6808. Rev 0 - first release (as preliminary datasheet) with new file number. FN6808.0 Applied Intersil Standards
12/5/08
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com 28
FN6808.0 December 5, 2008
KAD5512HP
Package Outline Drawing
L48.7x7E
48 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE Rev 0, 11/08
7.00 PIN 1 INDEX AREA 6 A B 36 37 4X 5.50 PIN 1 INDEX AREA 6 48 1 44X 0.50
7.00
Exp. DAP 5.60 Sq.
(4X)
0.15
25 24 48X 0.40
TOP VIEW
12 13 48X 0.25 4 0.10 M C A B
BOTTOM VIEW
0.90 Max
SEE DETAIL "X" C 0.10 C 0.08 C SEATING PLANE
SIDE VIEW
44X 0.50
9.80 Sq C 48X 0.25 5.60 Sq 0 . 00 MIN. 0 . 05 MAX. 48X 0.60
DETAIL "X"
0 . 2 REF
5
TYPICAL RECOMMENDED LAND PATTERN
NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to AMSEY14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal 0.05 4. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 5. Tiebar shown (if present) is a non-functional feature. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature.
29
FN6808.0 December 5, 2008
KAD5512HP
Package Outline Drawing
L72.10x10D
72 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE Rev 1, 11/08
10.00 PIN 1 INDEX AREA 6 54 A 4X 8.50 B 55 72 1
68X 0.50
PIN 1 INDEX AREA 6
10.00
Exp. DAP 6.00 Sq.
37 (4X) 0.15 36
TOP VIEW
18 72X 0.40
BOTTOM VIEW
19 72X 0.24
4
0.10 M C A B
0.90 Max
SEE DETAIL "X" C 0.10 C 0.08 C SEATING PLANE
SIDE VIEW
68X 0.50
9.80 Sq
72X 0.24
6.00 Sq
C
0 . 2 REF
5
72X 0.60
0 . 00 MIN. 0 . 05 MAX.
DETAIL "X"
TYPICAL RECOMMENDED LAND PATTERN
NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to AMSEY14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal 0.05 4. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 5. Tiebar shown (if present) is a non-functional feature. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature.
30
FN6808.0 December 5, 2008

▲Up To Search▲

Price & Availability of KAD5512HP

	To Download KAD5512HP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .